View NSVA468_571415.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NSVA468 Dec-01
JRC SAW FILTER
NSVA468
Application
433.92MHz DATA
Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1.
Table 1. Electrical Specifications Item Spec. Input and Output Impedance 50 Nominal Center Frequency (f0) 433.92MHz Insertion Loss 433.045~434.795MHz 3.0dB max. Response Variation 433.045~434.795MHz 1.5dB max. Input and Output VSWR 433.045~434.795MHz 2.5 max. Out of Band Rejection 412.52MHz 50dB min. (Relative to Through Level) 455.32MHz 50dB min. (Operating Temperature Range: -10~+60C)
Maximum Rating: (Table 2) Table 2. Maximum Ratings Item Maximum Input Power Maximum DC Voltage Operating Temperature Range Storage Temperature
Rating +20dBm 7.5V -10~+60C -20~+70C
Mechanical Specifications: (Fig.2) Package is designed as small as 5.2x4.5x1.5[mm3] for SMD (Surface Mount Device) type. Notice: This part is electrostatic discharge sensitive and may be damaged by improper handling.
Communications Equipment Division Communications Equipment Marketing Department
17-22 Akasaka 2-chome minato-ku, Tokyo. 107-0052 Japan Tel. +81 3-3584-8811 Fax. +81 3-3584-8876 http://www.jrc.co.jp/product/comm/deveice/saw/saw_top.html (Japanese) http://www.jrc.co.jp/product/comm/device/saw/saw_top_e.html (English)
NSVA468 Dec-01
IN 50
1 2 3
8 SAW 4
7 6 5
OUT 50
Fig.1 Measuring circuit
(1) (a) 5.20.2 (b)
4 .5 0 .2
J17
33A
(3)
(2)
(1.55)
(0 .8 )
[5x]
3
(1 .27) (0 .7 5 ) [2x ]
5 6 7 8
Fig.2 Package dimensions (in mm)
6.0 0.8 1.6 [6x]
[8x ]
4
(1.2)
Marking (1) Manufacture's Mark (2) Lot Number (a) Year (b) Month *Oct.--- X Nov.--- Y Dec.--- Z (3) Part number Mark Pin no. 1 2 3 4 5 6 7 8 Connection GND IN/OUT GND GND GND OUT/IN GND GND
1 .5 0 .2
2 1
(1 .27)
5.3
1.27
1.27
Via -Hole( 0.3)
Fig.3 Desirable land area (in mm)
0.8 [6x]
NSVA468 Dec-01
Notice
1. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -10C or more than +60C, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. 2. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350C max., the time of soldering: 10 seconds max., the power of soldering iron: 30W max.. 3. Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. 4. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. 5. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. 6. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. 7. As it might be a cause of degradation or destruction to apply D.C. voltage between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note 1. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products.
433.92MHz Specified Low Power Radio Station
FREQUENCY CHARACTERISTICS
0 1 2 Insertion Loss[dB] 3 4 5 6 7 8 9 10 Center 433.92 Frequency [MHz] S11 S22 Span 10 , 100 S21 0 10 20 30 40 50 60 70 80 90 100
11 10 9 8 7 6 5 4 3 2 1
S11
S22 11 10 9 8 7 6 5 4 3 2 1 Center 433.92
VSWR
Center 433.92 0 10 20 Insertion Loss [dB] 30 40 50 60 70 80 90 100 0
Span 25 [MHz]
VSWR
Span 25 [MHz]
1500 Frequency [MHz]
3000

▲Up To Search▲

Price & Availability of NSVA468

	To Download NSVA468 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .